- The most obvious gap in a short time is the cross section of this piece, hot dip galvanized barbed wire because it is the surface anti-corrosion treatment, so in the cross section of this piece will appear rust, and stainless steel barbed wire because the internal raw materials and surface raw materials are consistent, so there is no such situation.
- The acid activation solution in the production process can remove the corrosion products and oxide film on the surface of the low carbon steel wire without excessive corrosion to the matrix. Galvanized wire can be zincate galvanized or chloride galvanized process, should use appropriate additives to obtain the low carbon steel wire standard requirements of the coating. When galvanized wire after light plating should be light treatment. Control the temperature of the bath of galvanized wire.
Post time: 20-03-23- Galvanized wire is coated with a layer of stable zinc on the outside of the wire, and the zinc layer is used to protect the wire and make the service life of the wire longer. In the production of galvanized wire, the wire should be pickled. Pickling is to use some acid mist or acid liquid to wash away some oxides on the surface of iron, that is, rust, and some other corrosion, to achieve the purpose of cleaning iron, so that zinc will fall off when galvanized.
Galvanized wire coating has galvanized, aluminum, nylon or plastic coating. Zinc plating is divided into thin coating after steel wire plating and thick coating after steel wire drawing. The mechanical properties of thick coating are lower than that of smooth steel wire rope, and it is suitable for use in serious corrosive environment. Aluminized wire rope it is more resistant to corrosion, wear resistance, heat resistance than galvanized wire rope, using the method of production after the first plating. The wire rope coated with nylon or plastic is divided into two kinds: coated rope and coated rope.
Post time: 15-12-22
Post time: 17-08-22- Hot dip galvanizing is in the hot melt zinc liquid dip plating, production speed, thick but uneven coating, the market allows the thickness of 45 microns, up to 300 microns above. It is dark in color, consumes more zinc metal, forms infiltration layer with base metal, and has good corrosion resistance. Hot dip galvanizing can be maintained for decades in outdoor environment. The protection of zinc coating on iron matrix has two principles: on the one hand, although zinc is more active and easy to oxidize than iron, but its oxide film is not as loose and compact as iron oxide. The dense oxide layer formed on the surface inhibits the further oxidation of zinc in the interior.
Hot dip galvanizing, also known as hot dip zinc, is the method of forming a layer of zinc coating on the surface of the workpiece after oil removal and rust removal, showing a clean and infiltrating surface, immediately immersed in the plating tank of zinc melting in advance. Cold galvanizing is the same after the removal of oil, in addition to lure, showing no pollution, infiltration of the workpiece hung into a special electroplating tank on the cathode, the anode with zinc. Switch on the DC power supply, zinc ions on the anode migrate to the cathode, and discharge on the cathode, so that the workpiece is coated with a layer of zinc layer hot dip galvanizing method.
Some customers may not use the blade rope immediately when they buy it. Some are for retail and some are temporarily without the blade rope for site construction. At this time, customers need to follow up the characteristics of the blade rope for storage.
Post time: 22-06-22The characteristics of galvanized hexagonal net: easy to use; Save transportation costs. It can be shrunk into small rolls and involved in moisture-proof paper packaging, taking up little space. Coating thickness uniformity, stronger corrosion resistance; The construction is simple and does not require special technology; Strong resistance to natural damage and corrosion resistance and adverse weather effects; Can withstand a large range of deformation, and still not collapse. It has the function of fixed heat preservation and insulation.
6, passivation to remove hydrogen parts should be passivation after the removal of hydrogen, passivation before the application of 1%H2SO4 or 1% hydrochloric acid activation 5~15s. Passivation shall be treated with colored chromate unless otherwise specified in the design drawings.
Post time: 17-10-22Zinc adhesion on galvanized wire surface and thickness of zinc layer
- The quantity should be the same as the contract, cold drawing, carefully record the quantity of each specification and packing method. If there is a label, check whether the label is correct and take a photo to confirm. Each roll of iron wire is fastened with galvanized packing tape, and then tightly bound with a very strong transparent plastic bag. The outer layer of coated iron wire is wrapped with white braided cloth, and the outer layer of galvanized iron wire is wrapped with green braided cloth, so as to ensure that the packaging will not be lax in the transportation process. One end of the wire must be clearly marked and the other end left on the outer layer for easy connection by other wires.
Post time: 28-03-23
Post time: 02-03-23
Post time: 06-07-22
Post time: 22-03-23- 2. Dissolution treatment: Put the pickling steel wire into the dissolution tank, and dissolve the zinc powder with the bath liquid by heating, and the dissolved zinc liquid will adhere to the surface of the steel wire.
Post time: 17-06-24
Post time: 29-05-23Blade thorn rope because the volume is relatively large so thorn rope factory is used to packaging treatment.
Post time: 09-08-22Hardness is a commonly used property index in mechanical properties of metal materials. The iron wire factory introduces a fast and economical test method for hardness testing. However, for the hardness of metal materials, there is not a unified and clear definition including all test methods at home and abroad. In general, the hardness of a metal is often considered to be the resistance of the material to plastic deformation, scratches, wear, or cutting.
- Three is to do a good job of galvanized silk product production site clean and tidy, in accordance with the scientific method of operation to operate the production, the operator should wear the required dress. If it is hot dip galvanized wire products, we must do a good job of passivation treatment, will be able to effectively prevent discoloration, prolong the method of discoloration, can solve the problem of discoloration.
Post time: 23-03-23In GENERAL, THE HARDNESS OF A METAL IS OFTEN CONSIDERED AS THE RESISTANCE OF a MATERIAL TO COMPRESSION PLASTIC deformation, scratches, wear, or cutting. In the adjustment of zinc dip distance of galvanized wire, keep the original speed unchanged, according to the time of zinc dip, wire diameter, and then estimate the zinc dip distance. By adjusting the zinc dipping distance, the zinc dipping time of various specifications of steel wire is shortened by 5s on average compared with that before debugging, so that the zinc consumption is reduced, the zinc consumption per ton of steel wire is reduced from the original 61kg to 59.4kg.