- The cleaning agent used for cleaning has no effect on the adhesion of the coating and no corrosion on the base material. Acid activation Acid activation solution should be able to remove corrosion products and oxide film from the surface of parts without excessive corrosion of the matrix. Zinc plating may be zinc plated with zincate or chloride and appropriate additives shall be used to obtain a coating that meets the requirements of this standard. After light plating, light treatment is carried out. Passivated parts requiring hydrogen removal shall be passivated after hydrogen removal. Activation with 1% H2SO4 or 1% hydrochloric acid for 5 ~ 15s prior to passivation.
- The most obvious difference in a short time is the cross section of this piece, hot dip galvanized barbed wire because of surface anticorrosion treatment, so there will be rust in the cross section of this piece, and stainless steel barbed wire because the internal raw materials and surface raw materials are consistent, so there is no such situation.
Daily residents still have a demand for galvanized barbed rope, but often the quantity is not particularly large. If the barbed rope factory ships the goods, then the additional freight may be higher than the price of customers to buy the barbed rope in the market. Barbed rope factory for mass purchase of customers to sell their demand is relatively large, but also want to find a manufacturer for procurement is also reasonable. Customer procurement problems can be in the thorn rope factory more perfect introduction at the same time also let the customer more at ease.
The main factors causing metal rust: relative humidity of the atmosphere at the same temperature, the percentage of water vapor content and water vapor saturation content in the atmosphere, known as relative humidity. Under certain relative humidity, the corrosion rate of metal antirust oil is very small, but higher than the relative humidity, the corrosion rate increases suddenly. This relative humidity is called the critical humidity. When the humidity in the atmosphere is higher than the critical humidity, the metal surface will appear water film or water droplets, if the atmosphere contains harmful impurities, dissolved in the water film, water droplets, electrolytes and aggravate corrosion.
Different from the general zinc barbed rope, the zinc content of the surface of the high zinc barbed rope is very high, which can reach 6-8 times of the former, so that it has a great advantage in service life. Ordinary products begin to corrosion in three or five years, while the latter takes longer time to change. Stainless steel barbed rope is in the material aspect of protection so durability is also better, these two products are known for long service life, but is high in price.
- 3. Gently rub soapy water on its body and scrub gently with a towel. Make sure you don’t get anything in his eyes or it might scare him into attacking you (he might show his little fangs and claws).
Pressure lock steel grid plate is at each intersection of bearing flat steel and horizontal bar, the horizontal bar is pressed into bearing flat steel or pre-slotted bearing flat steel through the pressure, the fixed steel grid plate, called pressure lock steel grid plate. The cross bar of the pressure lock steel grid plate is usually flat steel.
Post time: 29-03-23- After a long time of use, it will not rust like the corrosion layer on the surface of hot dip galvanized barbed rope, because the internal material of stainless steel barbed rope is the same as the material on the surface.
Magnetic test method is the original common difference between austenitic stainless steel and ferritic stainless steel simple way, austenitic stainless steel is wrong magnetic steel, but after cold processing under large pressure will have a slight magnetic; But pure chrome steel and low alloy steel are strong magnetic steel.
Cold drawing wire is a metal cold processing, with wire rod as raw material, that is, the mouth of the steel bar. Cold drawing wire is a product produced by a series of processes such as shell stripping, which is a common wire. In the development and production of metal materials, cold drawing wire is a very common material, its performance is good, the range of use is very wide, manufacturers in processing are the use of cold processing to produce.
- Zinc dipping time should be adjusted according to the thickness of wire diameter. The method of adjustment is the length of the distance between the lead screw on the zinc pot and the ceramic sinking roller. Thick wire diameter zinc dipping time should be long, fine wire diameter zinc dipping time should be short, zinc dipping length in the range of 2~3.5m, which is also to reduce the zinc consumption of steel wire galvanized, is an aspect of maintaining the uniformity of zinc layer.
The production process of large rolls of galvanized wire is a level of drawing, through the mold into a slightly smaller diameter than the original. And so on down to the desired length. One pull is not desirable, must be numbered, from coarse to fine is dependent on metal ductility. If it changes too much it just breaks. After drawing to a certain diameter, galvanized, so that the finished product.
Hot dip galvanized coating is also relatively thick, but there is an uneven situation, for example, the thickness of the thin is only 45 microns, thick can reach 300 microns or even thicker, the color of this product is relatively dark. There is also a lot of zinc consumed in the production process. Zinc will form an infiltration layer with the metal. Its advantage is that it has good corrosion resistance. Electrogalvanizing, it is through the plating tank in the zinc one-way plating on the outside of the metal products, this way of making products is relatively slow, but its thickness is more uniform.
In general, the hardness of a metal is often considered to be the resistance of the material to plastic deformation, scratches, wear, or cutting. In the debugging of zinc wire dipping distance, keep the original speed unchanged, according to the time of dipping zinc, the diameter of steel wire, and then estimate the dipping distance. By adjusting the zinc immersion distance, the zinc immersion time of steel wire of various specifications is shortened by 5s on average compared with that before debugging, so that the zinc consumption per ton of steel wire is reduced from 61kg to 59.4kg.
- 3, twist the weight of hexagonal mesh production plant, the greater the weight, the more sufficient the material.
- The most obvious gap in a short time is the cross section. Because the hot-dip galvanized barbed rope is surface anticorrosive treatment, there will be rust in the cross section, while the stainless steel barbed rope because the internal raw materials are consistent with the surface raw materials, so there is no such situation.
The characteristics of large volume galvanized wire is smooth and bright surface, but wet will affect the brightness of galvanized wire, so we must pay attention to avoid humidity when storing, can support a shelf on the ground, so that galvanized wire and the ground isolation, so that it will not be affected by the surface moisture, there is to pay attention to the change of weather, to avoid galvanized wire rain. Galvanized wire has good toughness and elasticity, the amount of zinc can reach 300 g/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance.
- 1, the width and length of the hexagonal net (according to your actual needs, the width and length we can adjust flexibly).
- The acid activation solution in the production process can remove the corrosion products and oxide film on the surface of the low carbon steel wire without excessive corrosion to the matrix. Galvanized wire can be zincate galvanized or chloride galvanized process, should use appropriate additives to obtain the low carbon steel wire standard requirements of the coating. When galvanized wire after light plating should be light treatment. Control the temperature of the bath of galvanized wire.
Barbed rope is to use iron wire, through winding machine, through a variety of weaving technology, wound in the main line (stranded) made of isolation protection net. There are three ways to twist the barbed rope, as detailed below.
- Stainless steel barbed rope is in the material aspect of protection so durability is also better, these two products are known for long service life, but is high in price.
- Product features: hot dip galvanized electric welding mesh surface flat, uniform mesh, straight warp and weft wire, diagonal accuracy within 3-5 mm. The structure of the net surface is strong, strong integrity, with strong corrosion resistance, beautiful, wide use and other characteristics.
- The advantage of the steel mesh sheet is that the steel mesh sheet ensures the quality of the project and is made by the automatic and intelligent production line under the strict quality control of the factory. The mesh size, steel bar specifications and quality of the steel mesh are strictly controlled. Avoid artificial mesh leakage, bonding is not strong, bonding error and Jerry construction. The mesh steel has large rigidity, outstanding elasticity, uniform, accurate spacing and high welding point strength. Thus greatly improve the quality of the project.
- Five: Spray blade barbed rope specifications: BTO-10, BTO-12, BTO-18, BTO-22, BTO-28, BTO-30, CBT-60, CBT-65
Custom is made of low carbon steel silk woven, mesh structure he has the characteristics of corrosion resistance, high strength and ductility. Steel wire diameter up to 2.0mm-4.0mm, steel wire appearance is usually selected hot dip galvanized maintenance, galvanized maintenance layer thickness can be made according to customer needs, galvanized maximum can reach 300g/㎡.