- Zinc layer thickness: hot dip galvanizing of electric welding mesh, single coating thickness is generally 0.08 ~ 0.12mm, and it is a controllable index.
The whole welding process of galvanized steel wire mesh does not need special technological methods, good weldability. However, in a few cases, the welding process will present difficulties: the converter steel produced by the old smelting method has high nitrogen content and high impurity content, resulting in high cold brittleness, added aging sensitivity, lower quality of welded joints, and poor weldability.
Post time: 07-09-221, no paint and maintenance, long new not old, exempt you from maintenance fatigue and trouble, the lowest comprehensive cost. Stainless steel wire mesh can be used as poultry cage, egg basket, channel fence, drain tank, porch guardrail, anti rat net, mechanical protective cover, livestock and plant fence, grid frame, etc.
- After a long time of use, it will not rust after the corrosion layer on the surface of the hot-dip galvanized barbed wire has problems, because the material inside the stainless steel barbed wire is the same as the material on the surface.
Defects such as surface film and surface inclusions can be found and treated by conventional techniques in order to remove them locally from the surface of the deposition layer. Excess foam is formed when soap and surfactants such as saponified fats are brought into the tank.
In sulfur dioxide, hydrogen sulfide and Marine atmosphere, zinc corrosion resistance is poor, especially in the high temperature and high humidity atmosphere containing organic acid, galvanized wire galvanized layer is easy to be corroded. The uniformity of the galvanized layer on the surface of galvanized wire and the color of galvanized wire, the galvanized layer on the surface of high-quality galvanized wire is uniform, zinc adhesion is good, and the color is white, there is no leakage plating and rust points and other problems.
Post time: 04-01-23- Ring corn with: used as a ring corn net, generally use mesh 5cm*7cm or 5cm*5cm of the original galvanized welding net, wire diameter from 1.8mm-2.3mm, height of 1.2m – 1.8m.
Post time: 12-06-24- The quantity should be the same as the contract, cold drawing, carefully record the quantity of each specification and packing method. If there is a label, check whether the label is correct and take a photo to confirm. Each roll of iron wire is fastened with galvanized packing tape, and then tightly bound with a very strong transparent plastic bag. The outer layer of coated iron wire is wrapped with white braided cloth, and the outer layer of galvanized iron wire is wrapped with green braided cloth, so as to ensure that the packaging will not be lax in the transportation process. One end of the wire must be clearly marked and the other end left on the outer layer for easy connection by other wires.
Wire flexibility and elongation is good, can withstand the pressure of mechanical operation, in our country’s industry has played a very important role. There are many kinds of iron wire, the most common is to give black iron wire, galvanized iron wire. The corrosion resistance of the outer coating is effectively improved, but the phenomenon of crevice corrosion will be found after long-term use.
Steel wire and iron wire have many similarities, but carefully distinguish, will find that they are not only different in the material, but also in the product characteristics of the great difference. So when choosing, be sure to make a clear distinction between the two. Steel wire factory introduces steel wire carbon structural steel made above, generally not galvanized, used for machinery, spring. Black, very hard; Wire: made of mild steel (mild steel), galvanized, used for joining and binding. White and soft.
Post time: 21-09-22
Post time: 11-08-22- 2, see if solder joint is firm, net width on both sides of whether level off, the wire have broken wire phenomena (note: net length is the length of the wire), welded wire mesh of the solder joint is normal after precise voltage debugging, welding of welded wire mesh with graphite, strong, and the net width on both sides of the cutting time is according to the broken wire knife to ensure smooth on both sides, There will be no leakage cutting on both sides of the protrusion of the wire is not cut off the phenomenon, the wire is broken, because the wire is not used up even if the column hole is blocked by the wire can not enter the normal cause, such as broken phenomenon can appear on the surface of the electric welding network lack of a wire.
3, reduce the bivalent iron ion in the plating aid used for hot plating wire, reduce the formation of zinc slag
- 2, the cage must be strong
Crevice corrosion is a kind of corrosion in small area, especially in concealed position, which can form vicious corrosion cycle. Almost all the crevice corrosion can occur in a metal alloy, with gas containing active anionic neutral medium Z is easy to cause crevice corrosion, crevice corrosion often occurs in the aperture of 0.025 to 0.1 mm, because of long time gathered, the cracks will exist a series of impurities, coupled with the external environment of damp easily corrode the area of the gap is small.
- Twisting hexagon mesh production factory is the selection of low carbon steel silk woven, mesh structure he has corrosion resistance, high strength and ductility and so on. The diameter of steel wire can reach 2.0mm-4.0mm. The surface of steel wire is usually used for hot-dip galvanized maintenance. The thickness of galvanized maintenance layer can be made according to the needs of customers.
In view of this situation, many manufacturers are committed to ensuring the corrosion resistance of titanium and titanium alloy under the premise of increasing the hardness of titanium alloy, and surface carburizing is one of the typical processing technology means. Similar to the surface carburizing treatment of steel, the surface carburizing treatment of titanium alloy is to make the active carbon atoms, diffusion to the internal of titanium alloy, the formation of a certain thickness of higher carbon content of the carburizing layer, after quenching and tempering, so that the surface layer of the workpiece to obtain high carbon content of titanium alloy wire.
- Canary cage is also known as hibiscus cage, jade bird cage. Can be made of nickel-plated alloy or bamboo, for the refined round, square or rectangular (breeding cage) bird cage. The top of the cage has two kinds of flat top and dome, and the bottom of the cage is closed with a bottom circle. The circular cage is about 33 cm high and 20 cm in diameter; The square cage is 24.7 cm long, 24.7 cm wide and 33.8 cm high. The spacing of the cage is 1 cm, and the diameter is 0.2 cm. Cage bottom NEED NOT BAMBOO, MAKE IT WITH PLASTIC BOARD, bottom plate CAN move, FACILITATE PULL OUT WASH. Two perches are placed in the cage, and a food and drinking pot is placed in the cage. The cage has a board at the top of the cage to change the bird’s habit of looking up at the sky.
- 2, galvanized welding mesh away from acid and alkali corrosion effect of acid and alkali is electric welding mesh. If the electric welding mesh is accidentally stained with acid and alkali, it should be immediately washed with clean water, and then dried with dry cotton cloth.
- 4. Cooling: The galvanized steel wire needs to be cooled to reduce its temperature to room temperature.
Industrial rust prevention method: coated with asphalt, iron roof, coated with asphalt, you can prevent rust. Metal coating: Some metal surface will form a dense oxide film, can be coated on the surface of the metal composed of this metal screen. Such as: galvanized iron, tinplate plating, bicycle underwire and some medical equipment are coated with chromium and nickel.