Bridge protection system generally do not need to be specially installed special drainage system, the use of hexagonal mesh made of gabion mesh boxes, the inside of the filler are selected stones, these stones are not easy to wear, and between the stones and stones will retain some gaps, so it is very good to meet the drainage requirements.
In GENERAL, THE HARDNESS OF A METAL IS OFTEN CONSIDERED AS THE RESISTANCE OF a MATERIAL TO COMPRESSION PLASTIC deformation, scratches, wear, or cutting. In the adjustment of zinc dip distance of galvanized wire, keep the original speed unchanged, according to the time of zinc dip, wire diameter, and then estimate the zinc dip distance. By adjusting the zinc dipping distance, the zinc dipping time of various specifications of steel wire is shortened by 5s on average compared with that before debugging, so that the zinc consumption is reduced, the zinc consumption per ton of steel wire is reduced from the original 61kg to 59.4kg.
The error of construction welding net diameter should be controlled at 0.02 mm. For example, we buy wire diameter of 89 wire welding net, with a micrometer to measure the diameter, the diameter of the allowable range is 87 -91 wire. In this range is qualified welding net. Because the accuracy has been compared, but no one can control it so well in the production process. The welding net can be accurate to 0.01 mm, so the error is allowed.
- ⑹ can not open the groove 1 ~ 6mm thick metal sheet single-side welding double-sided forming.
When the coating of large galvanized wire is blistered in the process of galvanizing, the bath temperature should be checked first. If the bath temperature is not low, and then strengthen the removal of oil before plating, to prevent the base metal in acid corrosion. If you pay attention to these problems, the bubbling phenomenon still exists, it should pay attention to the dosage and quality of additives, then you can stop adding additives, with high current electrolysis for a period of time, to reduce the content of additives, observe whether the bubbling phenomenon is improved. If there is no improvement, check whether the additive has been stored for too long or whether it contains too many impurities.
In order to orchard special electric galvanized shaft wire in alluvial surface to partially remove the surface film layer, surface impurity and other shortcomings can be found and solved according to the basic technology; Excessive foam is caused by soap and soapable surface active substances such as human fat into the tank. A moderate rate of foam production would be fine. The large amount of fine homogeneous particles in the tank can stabilize the foam layer, but the accumulation of too much solid particles will cause explosion.
- In addition to these reasons, we should also pay attention to the tooling and process must be stable, and regular testing should be done to ensure the uniformity of galvanized layer.
Post time: 20-09-22
Post time: 17-05-22- 5. Maintenance and cleaning in the future
- In order to ensure the electrical conductivity of steel wire, manufacturers need to follow a number of standards and regulations. For example, in the galvanizing treatment of steel wire, the international standard ISO 1461 should be followed to ensure uniform zinc layer thickness and surface gloss. In wire drawing processing, excessive stretching should be avoided so as not to deform the wire or lose its mechanical properties.
Wire mesh even in the mining industry also has a higher reflection, because the selection of low-carbon materials to do the material so that it has a general iron net class does not have flexibility, concluded that its plasticity in use, and then can be used in hardware crafts deep processing production, as the wall plastering, leak prevention crack and so on. Its light net body, lower cost, more can let customers experience its economic benefits.
Post time: 10-04-23- 1, the width and length of the hexagonal net (according to your actual needs, we can adjust the width and length flexibly).
- Decorative hook mesh welding, generally more robust, but assume that the workers are new, scheduling machine skills are not high, it will appear to open the solder joint. Once this situation is presented, it will bring significant losses to customers and factories.
- All can do spring can be called spring steel wire, and high carbon is the highest carbon content. Features: WITH high strength and hardness, high elastic limit and fatigue limit (especially notched fatigue limit), cutting function is OK, but welding function and cold plastic deformation ability is poor.
- 3. Before cleaning the cage, put the birds in a safe place, and then clean out the garbage inside the cage. Clean it up with a sweep. Then use a wet rag to clean on site.
- The wire mesh is finished by fine welding of active welding equipment. The material can be divided into cold drawing wire, hot dip galvanized, cold galvanized, dip plastic and so on. To be used for bridge reinforcement, deck paving, building reinforcement, etc.
In our daily life, what we can bend with our hands is basically galvanized iron wire, not steel wire. It has a high zinc content, which ensures excellent toughness and resilience, as well as ultra-high corrosion resistance, which can be maintained in outdoor environments for decades. There are many practical galvanized iron wire, such as strong reliability, galvanized layer and iron together, forming a special metallurgical structure, in the use and transportation process, can ensure that it will not be mechanical damage.
Post time: 14-02-23- Galvanized hexagonal net is a kind of galvanized metal wire mesh, mesh shape is hexagonal.
Now it is more used in the binding of the construction industry. Compared with ordinary wire, it is also softer and has better luster. Use in daily life does not need to carry out maintenance and maintenance, saving a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. There are many kinds, which can be selected according to different uses. The device for making annealed wire is simple, and the utilization rate of the device is improved. The material properties of annealed wire can meet different processing needs.
Unless it is a specially customized model, the stainless steel blade barbed rope produced now is generally produced with a 22mm blade length mold, which is what we usually call bto-22 type. It doesn’t have to be the case that there are specifications from 11mm to 65mm. Unless the customer insists on customizing the specified length, the barbed rope manufacturer produces bto-22 stainless steel blade barbed rope.
Friends in the industry know that galvanized iron wire has two kinds of cold galvanized iron wire and hot galvanized iron wire, so what is the difference between cold galvanized iron wire and hot galvanized iron wire? Which is good?
Hot plating wire mixed rare earth and aluminum elements, make zinc liquid fluidity, more uniform coating, but also reduce zinc consumption. Hot-dip galvanized wire has better protective properties than cold galvanized wire, which makes it widely used in chemical experiment equipment. Hot plated wire coating is thick, so that it has good corrosion resistance, can be in the outdoor sun and rain and other harsh environment can be maintained for decades, so hot galvanized wire is widely used in construction, traffic guardrail and other outdoor facilities.
- 3, barbed rope protection net in the bridge, channel, should be toward the bridge head cone slope (or end wall) direction surrounded, should not leave for people, livestock can drill into the gap.