...
2025-08-15 01:30
764
...
2025-08-15 01:00
1965
...
2025-08-15 00:53
1300
...
2025-08-15 00:39
1498
...
2025-08-14 23:19
2521
...
2025-08-14 23:12
126
...
2025-08-14 23:02
2726
...
2025-08-14 22:58
2734
...
2025-08-14 22:57
1049
...
2025-08-14 22:54
2453
- >Dredge pumps are a special category of pumps used in the dredging process. Dredging is the process of transporting submerged sediments (usually sand, gravel or rock) from one area to another. Dredging takes place in the shallow waters of lakes, rivers or seas for land reclamation, dredging, flood control, new harbours or expansion of existing harbours. The various industries that use dredge pumps are therefore the construction industry, mining, the coal industry and the oil and gas industry.
- - Low noise level - Operating underwater results in low noise or even silent operation.
- Dry Installation
- Consider the following.
- Slurry Pump
- Stainless Steel, Duplex Stainless Steel, Ductile Iron, Grey Iron, etc. We can also provide natural rubber, elastomer rubber parts and pumps.
- As described below, there are several >types of pumps that are suitable for pumping slurries. However, before considering which technology to use, we must address several key issues.
- Metal and/or rubber pump bushings are used to combat the erosion of solid particles found in the slurry. Metal slurry pump housings are usually made of carbide to resist erosion caused by increased pressure and circulation. Sometimes wear-resistant steel is used on the pump casing so that the pump can be welded if repairs are needed.
- Slurry Pump
- Slurry Pump
- Types of damage to slurry pumps
- Slurry Pump
- Follow proper piping principles to ensure consistent and uniform delivery of mud to the pump.
- Slurry Pump
- Desire for higher efficiency than centrifugal pumps
- Series of TL >FGD pump is a single stage single suction horizontal centrifugal pump. It is mainly used as the circulation pump for absorbent tower in FGD applications. It has such features: wide range flowing capacity, high efficiency, high saving power. This series of pump is matched by tight structure X bracket which can save much space. Meanwhile our company develops many kinds of material targeted on the pumps for FGD.
- Slurry pump impeller, is one of the most important parts of centrifugal slurry pumps. Depending on the application, slurry pump impeller selection is crucial to slurry pump performance. Slurry applications can be especially hard on the impeller of slurry pumps because of their abrasive nature. In order slurry pumps operates efficiently and stand up to the test of time, impeller has to be selected properly for slurry pumps.
- Slurry Pump
- Find a professional slurry pump supplier
- Ideal for slurry pumps - Only rubber lined pumps combine strength and corrosion resistance to create a quality slurry pump.
- Step 4
- The Company Adopts Advanced Computer Aided Engineering Software
- A >dredge pump is a horizontal centrifugal pump that is the heart of a dredger. It is designed to handle suspended abrasive granular materials and solids of limited size. Without a dredge pump, a stranded dredger would not be able to deliver mud.
- Slurry pump seals
- There are several types of slurry pumps, the most common being: centrifugal and volumetric pumps.
- The Company Adopts Advanced Computer Aided Engineering Software
- - Low noise level - Operating underwater results in low noise or even silent operation.
- >Slurry Pump
- In a word, the wear-resistant properties of the slurry pumps are stronger, and the ability to convey particles is also stronger. Generally, the capacity of the slurry pump is larger than the mud pump, which is mainly used for coal and metal ore washing. The mud pumps are more suitable for abrasive slurry is not very strong.
- WY type pump casing is made of abrasion resistant metal, impeller material can be abrasion resistant metal or rubber. The submerged parts of WYJ are all lined with rubber, for transfer corrosive slurry.
- Quenching is defined as the introduction of a neutral fluid (usually water or steam) into the atmospheric side of the seal to prevent the formation of solids that may interfere with movement or be used for other purposes.
- Larger impellers made of more material. This is to compensate for the wear and tear caused by abrasive slurries.
- Sites often rely on centrifugal pumps to provide slurry service. These pumps (and their associated piping systems) require special provisions that demand detailed knowledge of the properties of solids and slurries to prevent wear, corrosion, erosion and other adverse effects such as solids settling. Specifying the optimum combination of speed, geometry and material requires a proper balance of often conflicting pump priorities; this requires consideration of stable operation, maximum wear life, operational flexibility and minimum energy consumption.
- Slurry pump power adjustment
- What is a dredging pump?
- If you want to know more information about the best slurry pumps wholesale, welcome to >contact us today or request a quote.
- Slurry Pump Selection
- The company uses advanced computer assistant engineering software to design products and technology, which makes our
- What is the best seal arrangement for the application?
- One problem with centrifugal pumps is that the velocity and shear forces within the pump may damage the slurry/solids. Typically, twin-screw pumps cause the least damage to solids in the slurry.
- -When pumping abrasive slurries, it is essential to use wear-resistant components with a high chromium content. But more is not always better - above 25%, the impeller becomes brittle.
- Determine the nature of the material to be pumped
- The slurry weight or consistency determines the type, design and capacity of the slurry pump required. If you have any questions about the best pump for your application, welcome to >contact us today or request a quote.
- -When pumping abrasive slurries, it is essential to use wear-resistant components with a high chromium content. But more is not always better - above 25%, the impeller becomes brittle.
- Sump drainage or washdown
- The dredge pump is designed to draw sediment, debris and other hazardous materials from the surface layer into the suction pipe and transport the material through the pipe to the discharge site. The pump must be able to handle common solid debris of various sizes that can pass through the pump, thus minimizing the downtime required for cleaning.
- Applications
- Slurry Pump
- What is a dredging pump?
- The Difference Between Flushing And Quenching in Slurry Pump Seals