- Pet cage has many types, and selective is bigger, pet cages are generally made of wire, with better coarse, then at the bottom with a wheel base, such a simple pet basket was made, in the wheel at the bottom of the mount is for the convenience of the mobile, a pet cages should also adapt to the location of the production in addition to a door, Convenient in pet feeding when more convenient.
- The zinc layer on the galvanized wire has good ductility, can be cold blanking, rolling, bending and other molding without damage to the zinc layer. The zinc layer of galvanized wire with thick zinc layer has fine crystallinity, uniform and no void, and good corrosion resistance. The zinc layer obtained by electrogalvanizing is very pure and corrodes slowly in the gas, liquid and fog of acid and alkali, which can effectively protect the steel matrix. Galvanized layer can also be chromate passivation into a variety of colors, beautiful and generous, with good decoration.
Post time: 17-10-22
Post time: 24-11-22
Post time: 28-07-22“Dry” hot dip galvanizing is also called “drying solvent method” hot dip galvanizing. Iron and steel work pieces through degreasing, pickling, cleaning, dipping aid solvent and drying, and then immersed in the molten zinc solution to galvanize. The co-solvent is usually hydrochloric acid, ammonium chloride, or ammonium chloride mixed with zinc chloride in aqueous solution.
Three methods of twisting the thorn rope: forward twisting, reverse twisting, reverse twisting.
Post time: 26-09-22- No less than 5 disks should be extracted from each inspection lot for diameter error inspection. 1 point of steel wire should be extracted from each disk to measure steel wire diameter, and the actual diameter of steel wire at this point should be taken as the average value of the two vertical directions. The diameter error of cold-drawn low carbon steel wire should conform to the rules in the table below. The unqualified inspection batches shall be checked one by one, and the qualified batches can be used for engineering.
The life of the “wire”, is actually “low carbon steel wire”, carbon content in less than 0.2%. The surface is usually coated with zinc plating because it is easy to rust. Under atmospheric conditions, the galvanized layer will not rust before most of the fall off, relatively soft. The life of the “steel wire”, is carbon content in about 0.6% of the “carbon steel wire”, or carbon content in about 0.8% of the “high carbon steel wire”, they have enough hardness and elasticity after appropriate heat treatment, high strength. Uses such as winding ordinary spring and so on.
Hot dip galvanized hexagonal net is made of low carbon steel wire by mechanized braided welding and then by hot dip zinc treatment. The net color is white and shiny, thick zinc layer, uniform mesh, flat mesh surface, solder joint tension resistance, high corrosion resistance. The surface of the steel wire is usually protected by hot-dip galvanizing, and the thickness of the galvanized protective layer can be made according to the requirements of customers. Hot-dip galvanizing hexagonal net is another kind of twisting mesh corresponding to the galvanizing hexagonal net.
- 3, whether positive and negative twist, whether bilateral silk is needed.
- According to different body shape, habits, bird cage can be divided into many species. The basic components of the bird cage are plate top, cage rack, cage bar, cage door, cage hook, dragon ring, bottom ring, bottom of the cage. The accessories are composed of poop board, sun bar, bird food pot, water tank, jade finger, horsetail string and so on.
Most people in addition to pay attention to the price of barbed rope, many people for hot-dip galvanized barbed rope or cold galvanized barbed rope will have questions, in fact, these two products, the price difference is not very big, so how to choose hot-dip galvanized barbed rope and electric galvanized barbed rope?
- Bridge bridge reinforcement is durable in poor function and aging, etc., through the wire mesh reinforcement, can prolong the service life of the bridge, avoiding the phenomenon of bridge cracks, subsidence and so on, wire mesh can play an obvious effect of crack in bridge reinforcement engineering, engineering construction speed, to enhance the crack resistance of concrete function, better economic benefit.
Post time: 20-02-23- First, cold galvanized wire production process before treatment. Before galvanizing, a series of pre-treatment work on the steel wire is required, mainly including pickling, dissolution and brine or alkali washing.
Domestic iron wire factory has been able to consume wire rope, radial low steel wire, umbrella steel wire, spring steel wire, bicycle saddle spring steel wire and other products. In the 1980s, hot – plated low carbon steel wire, fan net cover steel wire, carbon structure steel wire, bed steel wire and so on were also published. The elongation of wire is increased after annealing. Make the product more soft and increase the scope of application of the wire.
Post time: 20-07-22- 3. Before cleaning the cage, put the birds in a safe place, and then clean out the garbage inside the cage. Clean it up with a sweep. Then use a wet rag to clean on site.
- Barbed wire, on the one hand, is a great protection against livestock theft, because the surface is covered with sharp spikes that make it very difficult to penetrate through the barbed wire. On the other hand, because livestock generally have the habit of bumping, the barbed rope is used to circle, which makes the livestock dare not rush to collide with the barbed rope, so as to save the use cost of users.
- The key and important parts with tensile strength greater than 1034Mpa should be relieved of stress at 200±10℃ for more than 1 hour before plating, and the carburized or surface hardened parts should be relieved of stress at 140±10℃ for more than 5 hours. The cleaning agent used for cleaning shall have no effect on the binding force of the coating and no corrosion on the substrate. Acid activation Acid activation solution should be able to remove corrosion products and oxide film (skin) on the surface of parts without excessive corrosion on the matrix.
- At present, some manufacturers also use the process of sandblasting equipment for wire pretreatment, sandblasting process is carried out in the sandblasting room, but in the process of sandblasting, dust will permeate the whole sandblasting room, produce a lot of dust that is not easy to collect, and if the dust will be discharged at will.