- Zinc pot workers should be determined to do duty and responsibility. Do not leave the post without leave, always observe the change of hot plating wire galvanized layer, and according to the analysis results, master the asbestos block gap friction, how long it takes to press, replace the pressing face; Adjust the working face; Until all four sides of the asbestos block are used up, maintenance workers will continue to use the block after repair when necessary to reduce the consumption of asbestos block.
- Third, after the production process of cold galvanized wire treatment. Galvanized cold galvanized wire needs to go through a series of post-treatment processes to ensure its quality and performance.
- (4) Stop the use of more than two strands of galvanized iron wire around the operation method.
- Tolerance range: radial mesh deviation range is not more than ± 4%, zonal mesh deviation range is not more than ± 3%; Solder joint tensile strength exceeds the national standard.
Purpose of galvanized hexagonal net: building wall fixed, heat preservation, heat insulation; Power plant tied pipe, boiler warm; Anti-freezing, residential protection, landscaping protection; Raising chickens and ducks, isolating chicken and duck houses, to protect poultry; To protect and support seawalls, hillsides, roads and Bridges and other waterworks.
- Galvanized iron wire has good anti-corrosion and anti-rust ability, so it can be used in some outdoor guardrails or fences, especially on handicrafts, which are also of great use. Galvanized iron wire is not easy to rust and oxidation on the surface. Now a lot of hardware manufacturers are producing iron wire, and the iron wire is very easy to rust, if you need to use in outdoor or humid places, the general customer will require the use of galvanized iron wire equipment to give the wire a layer of zinc, the thickness can be determined according to user requirements.
Post time: 07-09-221. Eliminate caked zinc residue on zinc liquid surface
- Galvanizing refers to the surface treatment technology of plating a layer of zinc on the surface of metal, alloy or other materials to play the role of aesthetics and rust prevention. The main method used now is hot galvanizing. However, hot dip galvanizing industry has been developed with the rapid development of cold strip rolling in the past 30 years. The production process of hot-galvanized sheet mainly includes: raw plate preparation → pre-plating treatment → hot-dip plating → post-plating treatment → finished product inspection and so on.
In sulfur dioxide, hydrogen sulfide and Marine atmosphere, zinc corrosion resistance is poor, especially in the high temperature and high humidity atmosphere containing organic acid, galvanized wire galvanized layer is easy to be corroded. The uniformity of the galvanized layer on the surface of galvanized wire and the color of galvanized wire, the galvanized layer on the surface of high-quality galvanized wire is uniform, zinc adhesion is good, and the color is white, there is no leakage plating and rust points and other problems.
2. Check the stabbing rope of the blade on time
- 3. The surface adhesion of stainless steel pet cage contains acid, alkali and salt substances (such as alkali and lime water splashing on the decoration wall), which causes local corrosion.
Post time: 08-07-22The whole country is cooling down on a massive scale. People suddenly feel that winter is coming. In much of the north, the collection of central heating and heating has also begun. People who do not have central heating or do not want to use traditional heating choose air heating. As heating equipment enters the peak season, building network sales are also gradually increasing.
- Application: Building materials
- Hook net use value is still very high, has a very good sex, and its manufacturing concise generous, beautiful, not in high temperature will fade, you can save a sum of maintenance costs, but also according to the different needs of the site to change the shape, to meet the needs of the site.
The application of cold wire drawing is very wide today. What problems need to be paid attention to in the acceptance of cold wire drawing in galvanizing plant?
- Third, 201 is high manganese content, the surface is very bright with dark bright, high manganese content is easy to rust. 304 contains more chromium, the surface is matte, no rust. Put the two together and you have a comparison. The most important thing is that the corrosion resistance is different. The corrosion resistance of 201 is very poor, so the price will be much cheaper. Because of the low nickel content of 201, the price is lower than 304, so the corrosion resistance is not as good as 304.
In GENERAL, THE HARDNESS OF A METAL IS OFTEN CONSIDERED AS THE RESISTANCE OF a MATERIAL TO COMPRESSION PLASTIC deformation, scratches, wear, or cutting. In the adjustment of zinc dip distance of galvanized wire, keep the original speed unchanged, according to the time of zinc dip, wire diameter, and then estimate the zinc dip distance. By adjusting the zinc dipping distance, the zinc dipping time of various specifications of steel wire is shortened by 5s on average compared with that before debugging, so that the zinc consumption is reduced, the zinc consumption per ton of steel wire is reduced from the original 61kg to 59.4kg.
The large roll of galvanized wire is violently extinguished in oxygen and sparks radiate, while the sodium block and magnesium bar are extinguished in oxygen and no sparks radiate. This phenomenon is determined by the composition of large rolls of galvanized wire. The large rolls of galvanized wire used in the experiment are pig iron or steel wire, both of which are alloys of iron and carbon (complex substances containing the elements iron and carbon). When the carbon in galvanized wire is extinguished, carbon dioxide will be produced, and the solid will be changed into a gas, and the volume will shrink rapidly.
Cold galvanizing is also called electric galvanizing. It is the use of electrolytic equipment to remove oil, pickling, and then put the pipe into the solution of zinc salt, and connect the anode of the electrolytic equipment, place zinc plate on the opposite side of the pipe, and connect the positive pole of the electrolytic equipment to the power supply. A layer of zinc is deposited on the pipe fitting by directional movement of an electric current from the positive pole to the negative pole. Cold plated pipe fitting is processed before galvanizing.
Post time: 18-08-22Speaking of pets, we have to talk about parrots. Because it’s easy to take care of, and it can talk, talk to you, and make you laugh. Parrots love to climb, so there is a cage with bars that are made up of horizontal bars rather than vertical bars, because this makes climbing easier for the parrots.
- The strength of the hook net should be satisfactory: when the vehicle is traveling at 80 km/h, the hook net will not fall into the river when it bumps against the railings at a 15 degree Angle. The shape and color of the hook mesh should be in harmony with the surrounding natural environment. The phenomenon planning of important Bridges should be done well.
Annealing wire is widely used because it has a good elasticity and flexibility, in the annealing process can be good control of its hardness, it is mainly made of iron wire, more often used in the construction industry binding wire use. In the production of the wire factory, annealing wire will be processed according to the properties of the material, according to the needs of different to change its hardness degree, can make it has more advantages, can reduce the consumption of metal, reduce the cost of production.
- 2, the production and installation is simple and fast, the use of patented friction connection or special connection accessories for installation, greatly improve the installation efficiency.
Post time: 24-11-22